Dielectric Job Openings

Position

CNC Lathe Setup / Operator

Reports to

Department Lead Person

General Summary

CNC Set-up people set-up and operate CNC machines using work orders, blueprints, necessary fixtures and tooling. They perform inspection as required by the quality department. Production is run on the CNC equipment in a reasonable and timely manner.

Hours

1st Shift - 6:30 a.m. – 3:00 p.m.

Equipment Used

Shoda router, CNC routers, CNC milling machines, CNC lathes, CNC Saws, other equipment as needed.

Skills Required / Job Responsibilities

Basic

  1. Reading
  2. Writing
  3. Math-basic, fractions, possible trigonometry
  4. Computer Literacy, ability to enter data as required

Specific

  1. Determine requirements from work order blueprints and other custom supplied data.
  2. Do an appropriate set-up ensuring both productivity, quality, and optimum cycle time.
  3. Run test program
  4. Have first piece approved by quality department.
  5. Inspect parts per print specifications and inspection intervals determined by the Quality department.
  6. Continually look for ways to improve on machining and set-up of job with Engineering Dept.
  7. Perform visual inspection at all times.
  8. Attend company courses and assist on project teams when asked.
  9. Completion and update of job specific set-up documentation.
  10. All other tasks assigned and apparent. May be cross-trained for other positions.

Abilities Required

Basic

  1. Communications (Listening/Making suggestions) verbal and written.
    • Completion of job specific paperwork.
    • Computer/data entry of job specific material.
  2. Attendance/Dependability (Punctuality/Observing break schedules)
  3. Teamwork
    • Good Attitude
    • Safety/Housekeeping
    • Quality of work
    • Productivity
    • Complete instructed assignments
    • Willingness to work overtime

Specific

  1. Attention to detail, accuracy
  2. Visual acuity and manual dexterity
  3. Ability to receive and comprehend instructions
  4. Ability to perform complex set ups
  5. Knowledge of inspection equipment
  6. Neatness and organization

Work Environment

  1. CNC production area in plant
  2. Dusty
  3. Fast-paced
  4. Primarily standing, walking and bending
  5. Much wrist motion in clamping and unclamping

Experience Required

Education

High School diploma or equivalent. Must be capable of reading and understanding blueprints, inspection equipment and requirements on work orders.

Job Experience

Minimum 2-4 years machining and setup experience, with some programming knowledge.

Range of Weightlifting

Up to 70 pounds

Safety Equipment and Requirements

Hearing protection and eye protection is required and provided on the manufacturing floor. Observe all safety regulations of the department and the plant. Safety-toe footwear must meet and fully comply with American Society of Testing Materials (ASTM) Standard F2413-05, per OSHA Regulation Subpart l - Personal Protective Equipment, Section 1910.136 Foot protection, no loose clothing, hair or accessories.

Training Required in the Following Company Procedures:

SOP 200-03Corrective and Preventive Action
SOP 200-04Development of Process Control Plans
SOP 200-05Inspection and Testing
SOP 200-06Inspection and Test Status
SOP 200-07Control of Nonconforming Product
SOP 500-02Product Identification and Traceability
SOP 600-03Preservation of Product
SOP 900-01Process Control
SOP 900-03Preventive Maintenance

The above is intended to describe the general content of and requirements for the performance of this job. It is not to be construed as an exhaustive statement of duties, responsibilities, or requirements.

If you are interested in applying for this position, you may apply either of two ways:

Or apply in person at:

Dielectric Corporation
W141 N9250 Fountain Blvd.
Menomonee Falls, WI 53051

Dielectric is an Equal Opportunity Employer

 

Current Openings

CNC Lathe Setup/Operator

First shift hours are
6:30 am – 3:00 pm

Second shift hours are 3:00 pm – 11:30 pm